The Theta 30P compact programmable Transducers are available with LCD display and are completely on-site configurable.
Features
- True RMS measurement
- On-site configurable as: Active / Reactive / Apparent / Phase Angle / Power Facto
- On-site programmable inputs
- On-site selectable output; DC Current or DC Voltage
- Seven segment LCD display
Theta 50 is used to electrically isolate input, outputs & power supply. It fills all requirements & regulations concerning electromagnetic compatibility (EMC) & safety (IEC 61326-1 & IEC 61010-1-2010)
Features
• Accuracy class 0.2 as per International Standard IEC/EN 60 688
• Output Response Time < 250 ms
• Fast and easy installation on DIN RAIL or onto a wall or in panel using optional screw hole bracket.
Theta 10A/10V transducer converts a sinusoidal AC Current or AC Voltage into a load independent DC Current or a load independent DC Voltage proportional to the measured value.
Features
• Accuracy class 0.2 as per International Standard IEC/EN 60688
• Output Response Time < 250 ms
• Fast and easy installation on DIN RAIL or onto a wall or in panel using optional screw hole bracket.
The Theta 20A/20V compact programmable Transducers are available with LCD display and are completely on-site configurable.
Features
- True RMS measurement
- On-site programmable inputs
- On-site selectable output; DC Current or DC Voltage
- Single or Dual output
- Seven segment LCD display
P19 Temperature and Humidity Transducer.
Features
• Built-in temperature and humidity sensor
• Calculation of selected physical quantities (dew-point temperature, absolute humidity)
• Storage of measured and calculated maximum and minimum values
• Interface RS-485 galvanically isolated (Modbus protocol)
Transmitter Theta 60R available in 1 channel version, in housing S17 clipped on to a top – hat rail and 2 channel version, in housing S17 hole mounting brackets pulled out. The transmitter Theta R converts the input variable-a signal from a resistance thermometer Pt 100- to a temperature linear output signal.
Features
• Measuring ranges configurable with DIP switch and potentiometer
• Red LED’s indicator: an open or short-circuit
• Electric isolation between input & output 2.3kV and power supply to all other circuits 3.7kV – fulfils EN 61 010
• Provision for either snapping the transmitter onto top-hat rails or securing it with screws to a wall or panel
• Housing only 17.5mm wide (size S17) / low space requirement
P30U transducer is designed to convert temperature, resistance, standard voltage and current signals into a standard DC voltage or DC current signal.
P30U has programmable measurement and additional functions.
Programming parameters can be realized with the use of buttons, via RS-485 interface and free e-con software or Ethernet or any web browsers via Ethernet interface.The device fulfills the requirements of III installation’s category for the products designed to industrial application.
- Input: programmable.
- Output: programmable
- display: LCD 2 x 8 characters with backlit.
- Indication of exceeding the alarm values.
- Indication of exceeding the alarm values.
- programming the measurement averaging time.
P43 Three Phase Programmable Transducer.
Features:
- Measurement and conversion of power network parameters in 4-wire balanced or unbalanced systems.
- Tetra quadrant energy measurement (Ep+, Ep-, EQL, EQc).
- Programmable current and voltage transformer ratios.
- Detection and signalling of incorrect phase sequence.
The P17 transducer is destined to convert the signal from temperature, resistance or voltage sensors into a 4…20 mA current signal.
Features:
- Can be treated as an active load forcing a current proportional to input signal changes from the supplying circuit.
- Input: Input:Voltage 0…10V, 0…60mV.
- Output: 4…20mA.
- Supplied from a current loop.
- Overall dimensions: 6.2 × 99 × 77mm.
- input:100, 250, 400 V A.C.1 A, 5 A a.c. 20…50 Hz.
- output:0/4…20mA, 0…10 V RS-485 with Mod bus protocol.
- Measurement of averaging time.
- Value of output signal when limit value are exceeded.
- external dimensions: 22,5 x 120 x 100 mm.
P 30P Single Phase power network Transducer.
Features:
- Measurement of 1-phase power network parameters.
- Conversion of measured value in an output signal on the base of the individual characteristics 1 or 2
- Alarm relays with NO contact operating in 6 modes.
- Recording of input signals in internal memory, on SD/SDHC card (option)
- Protocol: Modbus TCP/IP, HTTP, FTP.
Programmable transducer P30O type is destined to convert of number of pulses, number of working hours, frequency, period and rotational speed into a digital or standard current or voltage signal.
Features:
- 2 universal pulse inputs.
- Mathematical functions for each input.
- Data recording.
- Firmware upgradeable by the user.
- External dimensions: 45 x 120 x 100mm
THETA PI 102: Programmable Dual output DC Isolator
The purpose of the THETA PI-102 is to electrically isolate input, outputs and power supply. The isolator fulills all requirements and regulation concerning electromagnetic compatibility EMC and safety (IEC61326-1 and IEC 61010-1:2010).
The device has one input and provides two independent outputs in an extremely small space.
Features:
- All input signal range and output signal range are user programmable.
- Electric isolation between input, outputs and power supply.
- Prevents false measurement due to spurious potentials.
- Processes live zero signals, provision for signal conversion.
- Electrical insulation between power supply versus all other circuits.
- 3.0 kV, and between input and outputs -2.3 kV.
